Extron-electronic MTP 15HD RS Series Manuel d'utilisateur télécharger pdf

Setup Guide — MTP 15HD RS Series

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500

+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

Setup Guide — MTP 15HD RS Series, cont’d

68-925-50

Rev. A 01 09

Po wer Supply

Output Cord

SECTION A–A

Ridges

Smooth

A A

Captive

Screw

Connector

Tie Wrap

16 (5 mm) Max.

Example of a typical MTP 15HD RS application

INPUT

Tx Rx

RS-232

MONITOR

Wire color

White-green

NOTE If you are using Enhanced

Skew-Free™ A/V cable, use the

TIA/EIA T568A standard only.

Green

White-orange

White-blue

Orange

White-brown

Brown

Wire color

T568A T568B

White-orange

Orange

White-green

White-blue

Green

White-brown

Brown

Blue Blue

Insert

TP Wires

Pins:

1 2345678

OUTPUT

Tx Rx

RS-232

Step 6 — Power

Wire the 2-pole captive screw connectors for the included

external 12 VDC power supplies as shown at right. Plug them

into all units.

Step 7 — Pre-Peak, Peaking, and Level

• Transmitter’sPre-Peakswitch— View the image and

set the Pre-Peaking switch for the best image quality

to correct for long cable runs of the entire sytem (including all daisy-chained

receivers).

• Receiver’sPeakingcontrol— View the image and adjust the

Peaking control for the best image sharpness. Minimum setting

(full counterclockwise) is zero peaking.

• Receiver’sLevelcontrol— View the image and adjust the Level

control for the best brightness level.

Step 8 — Skew compensation (SEQ receivers)

Pair skew can be measured with test equipment or by viewing a crosshatch test pattern.

The SEQ receivers have built-in skew compensation capabilities. Adjust the equalization

as follows:

a. Zero the skew delay for red, green, and blue by using a small

screwdriver to press and hold the Select button for 3 seconds.

When the Red, Green, and Blue LEDs all go out, release the Select

button.

b. Use UTP cable test equipment or examine the displayed image to

determine which video signal — red, green, or blue — is shifted

furthest to the right.

c. Select the furthest left video signal by using a small screwdriver to press and release the

Select button until the LED for the left-shifted color — Red, Green, or Blue — lights.

d. Slowly rotate the Adjust control clockwise until the selected color is properly

converged.

e. If the remaining colors are left shifted, repeat steps c and d.

1 2 3 4 5 6

H SYNC +

V SYNC +

C SYNC

SOG

VIDEO

END UNIT

Format

Output

Format

C Sync SOG Video

RGBHV

RGBS

RGsB

Component*

S-video*

Composite*

* Input video format must match.

PRE-PEAK

OFF

RGB

PEAKING

LEVEL

INPUT

RS-232

MONITOR

POWER

12V

.5A MAX

OUTPUT

MTP T 15HD RS

PRE-PEAK

OFF

RGBHV

RS-232

Rack Mounted

DisplayDisplay

Up to Eight

Total Receivers

Extron

MTP T 15HD RS

Extron

MTP RL 15HD RS SEQ

Extron

MTP RL 15HD RS SEQ

INPUT

BUFFERED

OUTPUT

POWER

12V

.5A MAX

1 2 3 4 5 6

H SYNC +

V SYNC +

C SYNC

SOG

VIDEO

SPARE

MONO AUDIO

MTP RL 15HD A S EQ

INPUT

BUFFERED

OUTPUT

POWER

12V

.5A MAX

MTP RL 15HD A

MTP RL 15HD A S EQ

1 2 3 4 5 6

H SYNC +

V SYNC +

C SYNC

SOG

VIDEO

SPARE

MONO AUDIO

TP Cable

Ground

Gnd

Receive

Tr ansmit

Connected

RS-232

Device Pins

MTP

Pins

JMP1

JMP2

JMP3

Unjumpered for

One-way (Default)

Jumpered for

Two-way

DELAY

RED

GREEN

BLUE

SELECT

This card provides quick start instructions for an experienced

installer to set up and operate any of the MTP VGA

video and RS-232 transmission systems.

Pre-installation — RS-232 Jumper

The receiver’s RS-232 circuits are factory-set to be

one-way, transmitter to receiver. If the system has

onlyonereceiver, jumper JMP 1 on the main board can be set for

two-way communication as shown at right.

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the

MTP transmitter and up to eight receiver(s) as required.

Step 2 — Transmitter inputs

• Connect a computer (VGA) video source to the Input

connector.

• Connect a VGA monitor to the Monitor connector.

• Plug an RS-232 device into the RS-232 port. Wire the

connector as shown below.

Step 3 — TP cables between units

• Terminate a TP cable as shown at right. Connect

it between the transmitter’s Output port and the

receiver’s Input port.

N If the unit is labeled “C7”, only CAT 7 cable

should be used.

• Fordaisy-chaining, connect up to eight TP

cables between a receiver’s Buffered Output

port and a daisy-chained receiver’s Input port.

Step 4 — Receiver outputs

• Connect a VGA monitor to the Output connector.

• Plug an RS-232 device into the RS-232 port. Wire the connector as

shown for step 2c, above.

Step 5 — Receiver DIP switches

• HSyncandV.Syncswitches— Set these switches up for positive sync

or down for negative sync.

• CompositeSync,(SOG),andVideo

switches— Set these switches as shown

in the table below right to output the indicated format.

• EndUnitswitch— Set this switch up if either of the

following is true:

 The receiver being conﬁgured is the only receiver

connected to the transmitter.

 The receiver being conﬁgured is the last receiver

in a daisy-chained system.

Installation 1

Résumé du contenu

Page 1 - Installation

Setup Guide — MTP 15HD RS SeriesExtron USA - West Headquarters+800.633.9876Inside USA / Canada Only+1.714.491.1500+1.714.491.1517 FAXExtron USA - Eas

Commentaires sur ces manuels

Pas de commentaire

Extron-electronic MTP 15HD RS Series Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Récepteurs et amplificateurs Extron-electronic MTP 15HD RS Series. Extron electronic MTP 15HD RS Series User Manual [en] [fr] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs et amplificateurs Extron-electronic MTP 15HD RS Series