Extron electronic MLC226IP Manuel d'utilisateur télécharger pdf

MLC 226 IP Series • Setup Guide

The Extron MLC 226 IP Series MediaLink

Controller integrates Ethernet connection into

AV systems to allow users to remotely control, monitor, and troubleshoot AV equipment, including display devices and

switchers. It includes an embedded web server, multiple serial ports, relays, and configurable digital I/O ports for use in

applications that require control and monitoring of multiple devices within an AV system.

The MLC 226 IP series of controllers are configured using the free Extron Global Configurator (GC) software. The MLCs

integrate seamlessly with Extron GlobalViewer

Enterprise (GVE) software and the free GlobalViewer web-based AV

resource management software for remote control applications. Global Configurator and other useful software applications

are available at www.extron.com.

A checklist of basic setup steps is provided at the end of this guide. For additional information see the help files and the

MLC 226 IP Series User Guide, available at www.extron.com.

Panels and Features

DISPLAY

MLC 226 IP

VOLUME

CONFIG

OFF

VCR DVD

LAPTOP PC

SCREEN

DOWN

AUTO

IMAGE

SCREEN

AUX

VIDEO

DOC

CAM

PROJECTOR

RS-232/IR

NORMALLY OPEN

RS-232 12V

CM/ IR SCP

A B C D E

1 2

COMMON

GROUND

RELAYS

IR/SERIAL OUT

MLS PWR

3 4

5 6

Tx/IR

GROUND

PWR SNS

GROUND

+12V OUT

GROUND

+12V IN

+12V OUT

GROUND

CONT MOD

IR IN

SCP COM

HOST

CONTROL

1=DIGITAL I/O

2=Tx 3=Rx 5=GND

38400, N, 8, 1

PRESS TAB WITH

TWEEKER TO REMOVE

INTERCOM

AUDIO

OUT

LAN

LAN (IP)

Connector

Side View

Host Control

and

Digital I/O

Port

Bottom Panel

Rear Panel

Power

Input

(12 VDC)

IR/Serial

Output

Ports

Control

Module/IR/

SCP Ports

Projector

Control

Port

Relay

Ports

IP Intercom

Ports

Reset Button

and LED

(on side)

MLS

Switcher

Port

Front Panel

Display On and

Off Buttons

Volume Knob

and LEDs

IR Control

Receiver

IR Learning

Receiver

Config (RS-232

host control) Port

Input Selection

Buttons

Function or

Room

Control

Buttons

Cabling and Features

Attach cables using the following wiring diagrams as a guide. Full details are available in the MLC 226 IP Series User Guide.

CAUTION: Installation and service must be performed by authorized personnel only.

Control — Projector or Display

Bottom

Panel

PROJECTOR

RS-232/IR

A B

Tx/IR

GROUND

PWR SNS

GROUND

+12V OUT

+12V OU

ROUND

CONT MO

Transmit (Tx)

Receive (Rx)

Ground ( )

IR transmit (Tx)

Ground ( )

Projector

or Display

IR Port

Receive (Rx)

Transmit (Tx)

Ground ( )

Bidirectional

Projector or

Display

RS-232 Port

+12VDC

Ground ( )

Power sense

Ground ( )

Digital input

Digital Input

oror

Sleeve ( )

Ring

(signal)

Tip (+12 V)

3.5 mm Stereo Plug

Extron

Power Sensor

(60-271-01)

On, high: >2.8 VDC

Off, low: <2.0 VDC

{

Infrared:

• TTL level (0 to 5 V)

• Up to 1 MHz

Digital input:

• High: >2.8 VDC

• Low: <2.0 VDC

Select RS-232 protocol via

software or SIS command.

Signals are bidirectional, ±5 V.

RS-232 default protocol:

• 9600 baud

• 8 data bits • 1 stop bit

• no parity • no flow control

NOTE: Each projector or display may

require different wiring. See the

manual that came with the projector

or display, or the Extron device driver

communication sheet for details.

Projector RS-232 / IR / Digital Input Port(s)

Contents

MLC 226 IP Series • Setup Guide 1

Panels and Features 1

Cabling and Features 1

Control — Projector or Display 1

Control — Control Modules, SCP Control Panels (CM/IR/SCP Port) 2

Control — Relay 2

Control — IR/Serial Output 2

Control — MLS Switcher 3

Power 3

Control — LAN (Ethernet) 3

Control — Serial (Host Control, Cong) and Digital I/O 4

Communication — IP Intercom 4

About Global Congurator (GC) 4

What It Does 4

What To Set Up in GC 5

Conguration 5

Resources 5

Obtaining Control Drivers 5

Instructions, Information, and Assistance 5

Conguring for Network Communication 5

Network Conguration Options 5

Network Conguration Using ARP 5

Mounting 6

Setup Checklist: How to Proceed With Installation 6

1 2 3 4 5 6

Résumé du contenu

Page 1 - Front Panel

1MLC 226 IP Series • Setup GuideThe Extron MLC 226 IP Series MediaLink® Controller integrates Ethernet connection into AV systems to allow users to re

Page 2 - Control — IR/Serial Output

2MLC 226 IP Series • Setup Guide (Continued)Control — Control Modules, SCP Control Panels (CM/IR/SCP Port)BottomPanelPROJECTORRS-232/IRCM/ IR/SCPA B

Page 3 - Control — LAN (Ethernet)

3Control — MLS Switcher12VRS-232GROUNDGROUNDGROUNDIR/SERIAL OUTMLS PWRAS BABS CRxTxGROUNDGROUND+12V IN12VGROUNDGROUNDGROUNDIR/SERIAL OUTPWRAS BLLS CGR

Page 4 - What It Does

4MLC 226 IP Series • Setup Guide (Continued)Control — Serial (Host Control, Cong) and Digital I/OCommunication — IP IntercomRINTERCOMAUDIOOUTAudio S

Page 5 - Resources

5By using GlobalViewer, users can manage, monitor, and control Extron and third-party equipment such as projectors, displays, computer monitors, Blu-r

Page 6

6MLC 226 IP Series • Setup Guide (Continued)Extron Headquarters+800.633.9876 Inside USA/Canada Only Extron USA - West Extron USA - East+1.714.491.15

Commentaires sur ces manuels

Pas de commentaire

Extron electronic MLC226IP Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Non Extron electronic MLC226IP. Extron electronic MLC226IP User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non Extron electronic MLC226IP