Extron electronic Extron Electronics Switch MTP R AV Manuel d'utilisateur télécharger pdf

PowerCage

™

MTP T AV and MTP R AV Board

Setup Guide

Continued on side 2.

The Extron

PowerCage MTP T AV and

MTP R AV are twisted pair transmitters and

receivers in a modular board format for the

PowerCage 1600 modular enclosure. They

transmit or receive composite video or

S-video and audio over CAT 5-type cable.

Both boards can be used with any CAT 5, 5e, or 6 cable, or Extron

Enhanced Skew-Free

™

A/V UTP cable for cable runs up to 1000 feet

(300 m). The boards mount in any of the 16 expansion slots at the rear of

the PowerCage 1600.

Refer to the PowerCage MTP T AV and MTP R AV User Guide and the

PowerCage 1600 Enclosure User Guide, available at www.extron.com.

NOTE: The hot-swappable, modular design allows for replacing or

upgrading boards in the ﬁeld at any time, without having to

power down the system.

Installation

1. Select an open slot at the rear, or take out a blank plate by loosening the two

screws (top and bottom), and lifting the blank away.

NOTE: If a board is already in the slot, loosen the screws and remove the board.

2. Remove the new board from the box,

holding the board by the frame.

3. Hold the board with the signal connectors

towards you and the MTP AV board name

and LED at the top, and align the top and

bottom grooves of the board with the slide

posts in the selected enclosure slot.

4. Carefully slide the board into the slot,

aligning that the two tabs on the lower

front end of the board with the matching

ports in the enclosure. Push the board

ﬁrmly into place.

5. Tighten the screws to secure the board.

6. If applicable, repeat steps 1 through 5

for any other modular boards.

NOTE: Cover all empty board slots; do not leave them open. Using a tool, securely

fasten the screws for boards and blank panels after initial installation and

subsequent removal and replacement of the boards.

MONO

AUDIO OUTPUT

1 2

SHARP

GAIN

Y/VID

INPUT

PowerCage

MTP R AV

Tx Rx

HD/SDI INPUT HD/SDI OUTPUTS

MODE

PowerCage

FOX 3G HD-SDI

1 2

REMOTE

RS-232

OVER FIBER

Tx Rx

ALARM

OUTPUT

RGB

PowerCage

FOX 4G RX RGB

Tx Rx

L R

AUDIO

5A MAX.

100-240V 50/60Hz

N15778

LISTED

1T23

I.T.E.

Screws

(2 per board)

1 2

REMOTE

RS-232

OVER FIBER

Tx Rx

ALARM

OUTPUT

RGB

PowerCage

FOX 4G RX RGB

Tx Rx

L R

AUDIO

Align board and

slide into slot.

16 Available Single Board Slots or

8 Double Board Slots

Power

Supply

MTP R AV

MONO

AUDIO OUTPUT

1 2

SHARP

GAIN

Y/VID

INPUT

PowerCage

MTP R AV

OUTPUT

PowerCage

MTP T AV

AUDIO INPUT

L R

Y/VID

MTP T AV

S-video

Composite

Video

Y/VID C

CY/VID

7. If power has been removed, reconnect and power on the PowerCage. The LED on

the board lights green and the new board is auto-detected.

8. Following the image at right, connect input or output

device cables to the the two BNC connectors for S-video

signals or for composite video signals.

1 2

Résumé du contenu

Page 1 - MTP T AV and MTP R AV Board

PowerCage™ MTP T AV and MTP R AV Board Setup GuideContinued on side 2.1The Extron® PowerCage MTP T AV and MTP R AV are twis

Page 2 - PowerCage Front Panel

Extron USA - West Headquarters+800.63 3.9876Inside USA / Canada Only+1.714.491.1500+1.714.491.1517 FAXExtron USA - East+800.63 3.9876Inside USA / Cana

Commentaires sur ces manuels

Pas de commentaire

Extron electronic Extron Electronics Switch MTP R AV Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Non Extron electronic Extron Electronics Switch MTP R AV. Extron electronic Extron Electronics Switch MTP R AV User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non Extron electronic Extron Electronics Switch MTP R AV